Model “O” Link Seal

Nitrile rubber is resistant to oils, fuel and many solvents (gasoline, motor oil, kerosene, methane, jet fuel, hydraulic fluid, water, etc.)

Type: Oil Resistant

Seal Element: Nitrile (Green)

NOTE: Not U.V. Resistant

Pressure Plates: Reinforced Nylon Polymer

Bolts & Nuts: Steel with 2-part Zinc Dichromate & proprietary corrosion inhibiting coating

Temp. Range: -40 to 210 F (-40 to 99 C)*


Contact Order Desk

Description

Link-Seal® modular seals are considered to be the premier method for permanently sealing pipes of any size passing through walls, floors and ceilings. In fact, any cylindrical object may be quickly, easily and permanently sealed, as they pass through barriers, by the patented Link-Seal® modular seal design.
Ductile iron, concrete, metal as well as plastic pipes may be hydrostatically sealed within walls to hold up to 20 psig (40 feet of static head). Electrical or telecommunications cable may be sealed within conduit as they enter vaults or manholes. The annular space between carrier pipes passing through casings may be sealed against the entry of water, soil or backfill material.

With a wide variety of hardware/ elastomer combinations, Link-Seal modular seals are easily configured to achieve the best possible match for service conditions encountered. High temperature seals, fire seals (Factory Mutual Approved) and oil resistant seals may be ordered to meet special or unique service applications. For the system approach, metal or non-conductive Century-Line® sleeves with water stops may be ordered with Link-Seal modular seals to ensure correct positioning and a water tight seal of the installation within poured concrete walls.
Link-Seal modular seals are also available for a wide variety of special applications, temperature extremes, exotic chemical combinations and for “out of round” or non-centered applications. Please contact factory for your special application.

 

BENEFITS

Saves time and money…

  • Link-Seal modular seals install in up to 75% less time compared to lead-oakum joints, hand fitted flashings, mastics or casing boots.

Positive hydrostatic seal…

  • Link-Seal modular seals are rated at 20 psig (40 feet of head), which exceeds the performance requirements of most applications.

Long seal life…

  • Link-Seal modular seals are designed for use as a permanent seal. Seal elements are specially compounded to resist aging and attack from ozone, sunlight, water and a wide range of chemicals.

Maximum protection against corrosion…

  • Standard fasteners have a two-part zinc dichromate and proprietary corrosion inhibiting coating.
  • Corrosion resistant 316 stainless steel available for maximum corrosion protection.

Certification/Approvals…

  • Factory Mutual Fire Approvals.
  • Also a wide variety of approvals from various Federal agencies, associations, code groups, laboratories and organizations.

ISO Quality Assurance…

  • Link-Seal modular seals are manufactured in an ISO 9001:2000 certified facility.

Configure a Link-Seal modular seal to match your application…

  • 16 sizes, color coded EPDM, Nitrile, & Silicone elastomers may be used with various hardware options to match performance characteristics with service conditions.

SPECIFICATIONS

  • Pressure resistant to 20psig (40 ft of head)
  • Standard  — EPDM – rubber (black)
  • Oil Resistant — Nitrile rubber (green)
  • Temperature resistant — Silicone rubber (gray)
  • Low Durometer for fragile pipe — EPDM rubber (blue) Shore 40 ± 5
  • Hardware Options – S316 Stainless Steel and Zinc Dichromate Coated Steel (1470 hr salt spray tested) hardware

ADDITIONAL INFORMATION

Model Sizing    –   Minimum Required Seating Width:

  • LS-200 / LS-275  –  2.25”
  • LS-300 / LS-315  –  3.00”
  • LS-325 / LS-340 / LS-360  –  4.00”
  • LS-400 / LS-410 / LS-425 / LS-475  –  5.00”
  • LS-500 / LS-525 / LS-575  –  5.00”
  • LS-615 / LS-650  –  6.00”

Please see the  LINK-SEAL® Modular Seal Technical Data Sheet  for more sizing and selection information